detail information

This scan shows the results from a pressed DVD-ROM disc (Baldur's Gate DVD-ROM).

This scan shows the result from a pressed DVD-Video disk (Indiana Jones and the last crusade). Notice the error jump when shifting to the second layer (the error level actually drops from the end of the first layer to the beginning of the second layer).

If you read below you will see that both the pressed DVD-discs are well within the standards.

Download the ECMA 267 Standard for DVD-ROM, the ECMA 337 Standard for DVD+R/RW and the ECMA 338 Standard for DVD-R/RW at http://www.ecma-international.org if you want to look at the standards for yourself. Here is some data from the ECMA standards (same for DVD-ROM, DVD-R/RW and DVD+R/RW):

Random errors:

A row of an ECC Block that has at least 1 byte in error constitutes a PI error. In any 8
consecutive ECC Blocks the total number of PI errors before correction shall not exceed 280.

Here we see what a PI error is defined as a row in an ECC block having 1 byte or more containing errors. And that the sum of PI errors in 8 ECC blocks after each other should not exceed 280 PI errors.

But what is a row and what is an ECC block? Again we refer to the ECMA standards. We do not copy and paste everything but if interested look in the ECMA standards. A row is 182 bytes long where the last 10 bytes contain PI (Parity Inner) information. An ECC block is 208 rows long where the last 16 rows contain the PO (Parity Outer) information. This gives us a maximum possible PI error amount of 208 errors per block and for 8 blocks after each other this sum is of course 8 times higher giving a maximum possible amount of 1664 PI-8 errors. In practical use a disc with 1664 PI-8 errors is unreadable.

According to our tests the specified max PI-8 sum of 280 for good discs seems to be a good guideline, as some readers have problems reading discs when the PI-8 errors is over 300 and most players starts to have problems when the PI-8 error level reaches 600 or more.

But what are the PO errors that K-Probe reports? Actually the PO errors that K-Probe reports is the Parity Inner uncorrectable errors, meaning errors left after PI correction. Only the ECMA 337 standard describes the Parity Inner uncorrectable errors. So how is a Parity Inner uncorrectable error defined? Here are what ECMA 337 states:

'If a row of an ECC Block as defined in 13.3 contains more than 5 erroneous bytes, the row is said to be 'PI-uncorrectable"."

In theory an ECC block may in the worst case have 208 PI uncorrectable errors since every ECC block is 208 rows long. But the ECMA 337 standard goes further and specifies the max amount of accepted PI uncorrectable errors allowed on a good disc:

'- In any ECC Block the number of PI-uncorrectable rows should not exceed 4."  

This means that when the PO sum is set to 1 the maximum error value should not exceed 4. The theoretical maximum value for PO errors is 208 errors.

But what makes a disc unreadable? A PO uncorrectable error will make the disc unreadable, but K-Probe does not display the PO uncorrectable errors.

Notice that there are other aspects such as disc reflectivity, jitter, tracking errors and so on that also will affect the readability of a DVD disc - but for this we do not have measuring equipment available.

And another note is that we have scanned the discs at 4X CLV speed, by lowering the speed to 2X(DVD-R/RW)/2.4X(DVD+R/RW) or 1X the amount of reported errors may drop on some discs. We scanned at 4X CLV due to lower speeds taking to much time.

To see if there is a connection between the reported amount of errors and readability of the discs we also include the reading curve from a Artec DHM-G48 16x DVD-ROM. Only the best of the best discs will be able to get a perfect reading curve, so our limit for good discs will be: A speed drop at the end is accepted, but the reading speed should not drop below 6x for longer periods (small dips below 6x are accepted).

Easier explanation on how to read the test results.

Maybe this got too technical, and you are wondering what to look for in Kprobe reports?

Use this as a guideline for good discs:

PI(Parity Inner): No larger areas on the disc should exceed 280 PI-8 errors, do not worry too much about high single spikes that exceed 280.
PO(Parity Outer): No larger areas on the disc should exceed 4 PO-1 (actually PI uncorrectable) errors, do not worry too much about high single spikes that exceed 4.

And as always; lower is better.

And look at the reading curve, some slowdowns is expected with most media, but the reading speed should not drop below 6x for longer periods (small dips below 6x are accepted).

DVD+R media compatibility and write quality:

Good media and kprobe result, the small drop in the reading curve at the end is not a problem.

Emtec DVD+R 8x Preliminary Samples

This media was given to us by MPOTEC and it is a preliminary sample! As we can see, the KProbe result is excellent.